| Both sides previous revisionPrevious revisionNext revision | Previous revision |
| fabwiki:research:canada:delijani [2018/05/08 18:23] – external edit 127.0.0.1 | fabwiki:research:canada:delijani [2023/10/18 16:33] (current) – [External Links] rpschmitz |
|---|
| <align center>**<fs x-large>The Evaluation of Changes in Concrete Properties Due to Fabric Formwork</fs>**\\ | ;#; |
| | <fs x-large>The Evaluation of Changes in Concrete Properties Due to Fabric Formwork</fs>\\ |
| <fs medium>by Farhoud Delijani</fs></align>\\ | <fs medium>by Farhoud Delijani</fs> |
| | ;#; |
| | \\ |
| \\ | \\ |
| \\ | \\ |
| <fs large>**ABSTRACT**</fs>\\ | <fs large>**ABSTRACT**</fs>\\ |
| |
| <align justify><fs medium> | ### |
| Fabric as a flexible formwork for concrete is an alternative giving builders, engineers, and architects the ability to form virtually any shape. This technique produces a superb concrete surface quality which requires no further touch up or finishing. Woven polyolefin fabrics are recommended for this application. A permeable woven fabric allows excess water from the concrete mix to bleed through the mold wall, and therefore reduce the water-cement ratio of the concrete mix. Due to the reduction in water-cement ratio, higher compressive strength in fabric formed concrete may be achieved, as also suggested by earlier research. The current research study was conducted to investigate and document the changes in concrete strength and overall quality due to use of commercially available woven polyolefin fabrics. Use of fabric formwork will contribute to decreased construction cost, construction waste, and greenhouse gas emissions. Two sets of tests were conducted as a part of this research study including comparison of compressive strength of fabric formed versus PVC formed concrete cylinders and comparison of behaviour of the fabric formed reinforced columns versus cardboard formed reinforced concrete columns. Variables in this research were limited to two types of fabric with different permeability (Geotex 104F and Geotex 315ST) and two types of concrete; concrete made with conventional Portland cement and no flyash herein called normal concrete (NC) and concrete with 30 percent flyash in its mix design (FAC).</fs></align> | <fs medium> |
| | Fabric as a flexible formwork for concrete is an alternative giving builders, engineers, and architects the ability to form virtually any shape. This technique produces a superb concrete surface quality which requires no further touch up or finishing. Woven polyolefin fabrics are recommended for this application. A permeable woven fabric allows excess water from the concrete mix to bleed through the mold wall, and therefore reduce the water-cement ratio of the concrete mix. Due to the reduction in water-cement ratio, higher compressive strength in fabric formed concrete may be achieved, as also suggested by earlier research. The current research study was conducted to investigate and document the changes in concrete strength and overall quality due to use of commercially available woven polyolefin fabrics. Use of fabric formwork will contribute to decreased construction cost, construction waste, and greenhouse gas emissions. Two sets of tests were conducted as a part of this research study including comparison of compressive strength of fabric formed versus PVC formed concrete cylinders and comparison of behaviour of the fabric formed reinforced columns versus cardboard formed reinforced concrete columns. Variables in this research were limited to two types of fabric with different permeability (Geotex 104F and Geotex 315ST) and two types of concrete; concrete made with conventional Portland cement and no flyash herein called normal concrete (NC) and concrete with 30 percent flyash in its mix design (FAC).</fs> |
| | ### |
| |
| <align justify><fs medium>The laboratory results revealed that fabric Geotex 315ST is an ideal geotextile for forming concrete. It was also found that the effects of fabric formwork on concrete quality in a large member are limited mostly to the surface zone and the core of the concrete remains the same as a conventionally formed concrete. Even though fabric formed cylinder tests showed an average of 15% increase in compressive strength of the concrete samples, compressive strength of the reinforced columns did not dramatically change when compared to the companion cardboard formed control columns. This research confirmed that fabric formwork is structurally safe alternative for forming reinforced concrete columns.</fs></align>\\ | ### |
| | <fs medium>The laboratory results revealed that fabric Geotex 315ST is an ideal geotextile for forming concrete. It was also found that the effects of fabric formwork on concrete quality in a large member are limited mostly to the surface zone and the core of the concrete remains the same as a conventionally formed concrete. Even though fabric formed cylinder tests showed an average of 15% increase in compressive strength of the concrete samples, compressive strength of the reinforced columns did not dramatically change when compared to the companion cardboard formed control columns. This research confirmed that fabric formwork is structurally safe alternative for forming reinforced concrete columns.</fs>\\ |
| | ### |
| |
| <columns 100% 33.333% 33.333% - > | <columns 100% 33.333% 33.333% - > |
| |
| ==== TABLE ==== | ==== TABLE ==== |
| <align left> | |
| | #;; |
| [[fabwiki:research:canada:delijani:chapter_1|INTRODUCTION]]\\ | [[fabwiki:research:canada:delijani:chapter_1|INTRODUCTION]]\\ |
| Background and History\\ | Background and History\\ |
| Test Results\\ | Test Results\\ |
| Finish Effect of Vibration on Concrete Surface\\ | Finish Effect of Vibration on Concrete Surface\\ |
| </align> | #;; |
| | |
| <newcolumn> | <newcolumn> |
| |
| ==== OF ==== | ==== OF ==== |
| <align left> | |
| | #;; |
| [[fabwiki:research:canada:delijani:chapter_4|STRENGTH TESTS]]\\ | [[fabwiki:research:canada:delijani:chapter_4|STRENGTH TESTS]]\\ |
| Casting and Testing Concrete Cylinders with Fabric Formwork\\ | Casting and Testing Concrete Cylinders with Fabric Formwork\\ |
| Compressive Strength\\ | Compressive Strength\\ |
| Lessons Learned About Fabric Formwork\\ | Lessons Learned About Fabric Formwork\\ |
| </align> | #;; |
| | |
| <newcolumn> | <newcolumn> |
| |
| ==== CONTENTS ==== | ==== CONTENTS ==== |
| <align left> | |
| | #;; |
| [[fabwiki:research:canada:delijani:chapter_6|SUMMARY and CONCLUSIONS]]\\ | [[fabwiki:research:canada:delijani:chapter_6|SUMMARY and CONCLUSIONS]]\\ |
| Summary\\ | Summary\\ |
| Maximum Axial Load\\ | Maximum Axial Load\\ |
| [[fabwiki:research:canada:delijani:appendix_e|Appendix E:]] All Columns Test Result Curves\\ | [[fabwiki:research:canada:delijani:appendix_e|Appendix E:]] All Columns Test Result Curves\\ |
| </align> | #;; |
| | |
| </columns> | </columns> |
| |
| |
| <fs medium>[[http://www.umanitoba.ca/cast_building/|The Centre for Architectural Structures and Technology (C.A.S.T.)]]</fs> | <fs medium>[[http://www.umanitoba.ca/cast_building/|The Centre for Architectural Structures and Technology (C.A.S.T.)]]</fs> |
| | ~~UP~~ |
